EXTERNAL PROVIDERS


Results 1 to 1 of 1
  1. #1
    Alderperson
    Anko's Avatar
    Sexy A.I. Girls
    Awards:
    Posting Award

    Status
    Offline
    Join Date
    Apr 2010
    Location: Bringin the art Here!
    Posts
    1,018
    Images:
    254

    Green Answer Softening Skin & Adding Texture Back In

    Excerpt from Professional Portrait Retouching Techniques for Photographers Using Photoshop

    This one takes a few steps, but itís not hard at all. In fact, itís simple, so donít let the number of steps throw you. Also, at one point it does have a teeny, tiny bit of blur in it, but not enough to hurt anybody. It uses the Surface Blur filter at one stage, but donít worry, the whole idea of this technique is to have loads of texture, so donít freak out when you see the Surface Blur filter.
    Step One:
    As always, before you do any skin softening, remove all the major blemishes using the Healing Brush (see page 86). Here, I removed them already, so we can just focus on softening the skin. Start by pressing Command-J (PC: Ctrl-J) to duplicate the Background layer, as shown here.

    Step Two:
    Go under the Filter menu, under Blur, and choose Surface Blur. There are big advantages to using this filter over Gaussian Blur, and one is that it does a better job of preserving edges (rather than Gaussian Blur, which just blurs everything equally). I set the Radius (which controls the amount of blur) to around 39, and I make sure the Threshold slider (which controls the tonal values that get blurred) doesnít get higher than the Radius amount (here, I have set it to 31, and I usually have it between 5 and 10 lower than the Radius setting). This gives a blocky, almost posterized look to your subjectís skin at this point. Go ahead and click OK to apply this filter to your image (itís doing a lot of math to make some parts blurry while the edges maintain detail, so donít be surprised if a progress bar appears onscreen, as this one usually takes a few extra seconds to apply).

    Step Three:
    Now, go to the Layers panel and lower the Opacity of this Surface Blur layer to 50% (as shown here). Although it looks a lot better at this point (and the skin looks pretty decent), the rest of the image also has the effect applied. We just want it on her skin, so weíre going to have to mask it.

    Step Four:
    Press-and-hold the Option (PC: Alt) key and click once on the Add Layer Mask icon at the bottom of the Layers panel. This adds a black layer mask to your blurry layer (seen here to the right of the top layer), which hides the blurry layer, so all youíre seeing now is the original, unblurred Background layer. Press D to set your Foreground color to white, get the Brush tool (B), and choose a medium-sized, soft-edged brush from the Options Bar. Now, paint over her skin, but be careful to avoid all the detail areas, like her eyes, hair, clothing, eyebrows, nostrils, lips, etc.

    Step Five:
    To make sure you havenít missed any areas, in the Layers panel, Option-click (PC: Alt-click) directly on the layer mask thumbnail (as shown here). This displays just the mask by itself, and any areas on her face that appear in black arenít getting the effect, so youíll see instantly whether you missed any areas or not. These missed areas are really easy to fixójust take your Brush tool and paint right over them (youíre painting right on the mask itself, so youíll be able to see perfectly as you paint). Here, you can see I missed a bunch of areas on her forehead and by her nose, and a few tiny areas here and there. When youíre done (donít forget her neck and shoulders), Option-click directly on the layer mask thumbnail again to return to your normal image.

    Step Six:
    Now that you can see your full-color image again, youíre going to load your layer mask as a selection. So, press-and-hold the Com-mand (PC: Ctrl) key and click once directly on the layer mask thumbnail (as shown here). This loads your mask as a selection, as seen here. Remember, that selection is made from your mask, and your mask is a selection of all her skin, but without her eyes, nostrils, mouth, and the other detail areas included.

    Step Seven:
    While your selection is still in place, go to the Layers panel and click on the Background layer (this is original unsoftened layer). Now, press Command-J (PC: Ctrl-J) to take just that selected area and put it on its own layer (as seen here, where just her original unretouched facial skin is on its own layer now).

    Step Eight:
    In the Layers panel, click-and-drag that ďjust the skinĒ layer up to the top of the layer stack (so itís the top layer, as seen here). Now, weíre going to bring out the texture in her skin by going under the Filter menu, under Other, and choosing High Pass. When the dialog appears, drag the Radius slider all the way to the left (so the preview looks solid gray), and then drag the slider to the right until you see lots of nice skin texture coming through your solid gray image. Stop when you see a glow starting to develop (here, I was able to go to around 6.4. When I went too much higher, things started to glow). Click OK.

    Step Nine:
    To have your skin texture layer blend in with your softened skin layer below it, go to the Layers panel and change the blend mode for this High Pass layer from Normal to Soft Light (as shown here). Thereís now a layer of skin texture over your softened layer (so basically, you softened and smoothed the skin, then brought back some skin texture on top to bring back the detail lost by running the Surface Blur filter).

    Step 10:
    This face texture (High Pass) layer on top gives you its full effect (the most texture) when the layerís Opacity is set at 100%. If you lower the Opacity, it actually makes the skin softer, because youíre lowering the amount of texture. Here, Iíve lowered the Opacity of the High Pass layer a bit to soften up the skin a little more, because thereís plenty of texture visible in the image. Whether you lower the texture amount or not is totally your call, but youíll make that call based on the skin of your particular subject. A before/after of the retouch is shown here.

    Last edited by TCG-Admin; 03-05-2015 at 03:20 PM.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Question Time is Back (and more!)
    By Anko in forum Anko's Photoshop Tutorials
    Replies: 0
    Last Post: 02-03-2011, 09:06 PM
  2. Adding Files for Download
    By TCG-Admin in forum Site Instructions and Documentation
    Replies: 0
    Last Post: 12-29-2010, 04:09 AM
  3. How to Draw Lower Back Tattoos
    By Anko in forum Learn How To Draw - Freehand
    Replies: 0
    Last Post: 08-31-2010, 07:24 AM
  4. Quick Tip: How to Smooth Skin Without Losing Texture in Photoshop
    By Anko in forum Anko's Photoshop Tutorials
    Replies: 0
    Last Post: 05-26-2010, 12:41 PM
  5. Back To Life
    By Torkuitsu in forum Lyrics and prose
    Replies: 1
    Last Post: 10-26-2009, 11:15 PM